Previous Article | Next Article ![]()
Journal of Clinical Microbiology, July 2003, p. 3299-3305, Vol. 41, No. 7
0095-1137/03/$08.00+0 DOI: 10.1128/JCM.41.7.3299-3305.2003
Copyright © 2003, American Society for Microbiology. All Rights Reserved.
Department of Virology, Institute of Medical Microbiology and Hygiene, University of Freiburg, 79104 Freiburg, Germany,1 Department of Arbovirus, Instituto Evandro Chagas, 66090-000 Belém, PA, Brazil2
Received 30 September 2002/ Returned for modification 22 December 2002/ Accepted 12 April 2003
|
|
|---|
|
|
|---|
The diseases elicited by Orthobunyavirus range from typical viral diseases with flu-like symptoms (e.g., caused by Tahyna virus [TAHV]) (34) to febrile arthralgia (e.g., caused by Oropouche virus [OROV]) (26), encephalitis (e.g., caused by La Crosse virus [LACV]) (35), and, as recently reported, even hemorrhagic fever (caused by Garissa virus) (4). Although most infections have a rather mild outcome, some can be deadly (15, 33).
Many orthobunyaviruses are underestimated with regard to their potential prevalence and distribution. Snowshoe Hare virus (SSHV), Inkoo virus (INKV), TAHV, and Batai virus (BATV), originally isolated in the United States (14), Finland (30), the Czech Republic (3), and Slovakia (2), respectively, have all been isolated in Siberia (20-22). TAHV and BATV have been isolated in several Western European countries (19), and the isolation of BATV has also been reported in Sudan (24) and India (12).
Some orthobunyaviruses have gradually become accepted as etiological agents of growing disease problems. LACV and related viruses from the California serogroup cause about 100 cases of encephalitis per annum in the United States (6). Oropouche fever caused by OROV has developed into the second most common arboviral disease, next to Dengue fever, in Brazil (27).
In recent decades, evidence has accumulated indicating that, especially in developing countries, the complex interaction of factors such as the growth of the human population, the accompanying demographic and rapid socioeconomic changes, urbanization, and ecological upheaval contribute to the emergence of new infectious diseases (36).
As an initial measure to counter the development of these diseases into major public health problems, it is essential to gather basic clinical and epidemiological data (8). Modern diagnostic detection and identification tools can help to provide answers to urgent questions about the incidence, prevalence, and epidemiology of currently emerging diseases and about pathogens that have the potential to emerge in the future. They can also help researchers pick up the trail of several viruses isolated 20 to 30 years ago (Bunyamwera virus [BUNV], Germiston virus [GERV], and Guaroa virus [GROV]) and used to study the molecular biology of the Bunyaviridae but for which essential information regarding public health issues are almost completely missing.
Our aim was to devise rapid diagnostic tools for human pathogens of the genus Orthobunyavirus. Therefore, we developed one-step TaqMan reverse transcription (RT)-PCR assays for all viruses for which sequence information was available and established quantification standards for each virus. A single set of reaction conditions and one temperature profile was used for all TaqMan RT-PCR assays. Here we describe the TaqMan RT-PCR protocols and present data from the testing of OROV serum samples collected during an outbreak in Brazil.
|
|
|---|
Virus culture and RNA preparation. Viruses were grown in BHK-21 cells (INKV, TAHV, GROV, SSHV, and LACV), VeroE6 cells (JCV, California encephalitis virus [CALV], and OROV), or both (GERV) in 95% Dulbecco's modified Eagle medium-5% fetal calf serum in 175-cm2 flasks at 37°C in an atmosphere of 5% CO2. Each strain was passaged three times. RNA was prepared using RNeasy columns (Qiagen, Hilden, Germany) according to the manufacturer's instructions.
RT-PCR and cloning of S segments.
One-step RT-PCR was performed using the RT enzyme RAV-2 (Amersham Pharmacia, Freiburg, Germany) and the polymerase Tth (Roche, Mannheim, Germany) as recommended by Kuno (17). Briefly, 1 µM concentrations of the S segment primers (Table 1) were used for RT-PCR amplification from viral RNA by using the following profile: RT at 53°C for 30 min and 30 cycles of PCR at 95°C for 60 s, 60°C for 60s, and 72°C for 60s. The annealing temperature differed for BUNV (55°C). Reaction mixtures contained 1 U of RAV-2, 1 U of Tth, and 500 µM concentrations of deoxynucleoside triphosphates (dNTPs) in 10 mM Tris-HCl (pH 8.9), 100 mM KCl, 3 to 5 mM MgCl2, 50 µg of bovine serum albumin (BSA)/ml, and 0.05% Tween 20. Betaine (1 µM) was added to amplify the S segments of CALV and OROV. Amplicons were ligated into pCRII, and ligations were transformed into Escherichia coli inv
cells by using a TA cloning kit (Invitrogen, Breda, The Netherlands). Clones carrying a positively oriented DNA copy of the S segment were propagated in 50-ml overnight cultures, and plasmids were prepared by using a Maxiprep kit (Bio-Rad, München, Germany). The plasmids were sequenced using an ABI 377 sequencer to confirm the sequence identity.
|
View this table: [in a new window] |
TABLE 1. Primers for S segments and species-specific RT-PCR
|
RT-PCR amplicon design. Amplicons were placed into conserved regions of sequence alignments done with the Megalign software (DNAstar; Lasergene). Primers were designed for an annealing midpoint temperature (Tm) of 60°C by using the PCR document window of the Primer-Express software (Applied Biosystems), which operates by using the algorithm developed by Rychlik et al. (28). Species-specific amplicons were designed in conserved regions. Primer Tm ranged between 58 and 60°C, and the Tm of the 5'FAM- and 3'TAMRA-tagged probes ranged from 68 to 70°C. Species-specific primers were designed in reference to sequences with the following accession numbers: K00108 and K00610 (LACV); U12797 (CEV); U12796 and U12799 (JCV); J02390 and U12800 (SSHV); Z68497, U47142, and X73468 (TAHV); Z68496, U47137, and U47138 (INKV); D00353 (BUNV); M19420 (GERV); X37466 (GROV); and AF164531-58 (OROV). Nested primers were designed to hybridize to the S segment of OROV.
RT-PCR conditions. The RT-PCR conditions for the ABI-PRISM 7700 (Applied Biosystems) were as follows: 53°C for 30 min and 40 cycles of 95°C for 15 s and 60°C for 60 s [reaction mixtures in a total volume of 25 µl contained 2.5 U of RAV-2-2.5 U of Tth, 500 µM dNTPs, 10 U of RNasin, and 2 µM Rox in 50 mM Bicine (pH 8.2), 115 mM potassium acetate (KOAc), 5 mM Mn(OAc)2, 8% glycerol, 1 µM concentrations of primers, and 600 nM concentrations of probes]. To increase sensitivity, 2 µg of the single-strand binding protein GP32 (Roche) was added per reaction (32). RT-PCR conditions for the LightCycler (Roche) were as follows: RT at 61°C for 20 min, activation at 95°C for 5 min, and 40 cycles of PCR at 95°C for 5 s and 60°C for 15 s. We used a RNA master hybridization probes kit with 500 nM concentrations of primers and 200 nM concentrations of probes. This kit includes an aptamer-blocked Tth which performs both RT and hotstart PCR amplification. RT-PCR conditions for the SmartCycler (Cepheid) were as follows: RT at 53°C for 5 min and 40 cycles of PCR at 95°C for 5 s and 60 to 63°C for 15 s [reaction mixtures in a 25-µl total volume contained 1 U of RAV-2-1 U of Tth, 500 µM dNTPs, 500 nM concentrations of primers, and 200 nM concentrations of probes in 50 mM Bicine (pH 8.2), 115 mM KOAc, 5 mM Mn(OAc)2, 8% glycerol, and SmartCycler additive reagent (200 mM Tris-HCl, pH 8.0, 200 ng of BSA/ml, 0.15 M trehalose, 0.2% Tween 20)]. To increase sensitivity, 2 µg of the single-strand binding protein GP32 was added per reaction. We had to adapt hybridization temperatures to 62°C for BUNV and JCV and 63°C for GERV, JCV, SSHV, INKV, and TAHV, but they remained at 60°C for GROV, CEV, and BATV. The nested PCR conditions were as described above for the amplification of S segments, with 25 cycles for each round and hybridization at 52°C. Outside primers OROSFUP and OROSFDP and nested primers ORO N5 and ORO N3 have been described previously (29) (Table 1).
RNA preparation of patient samples. RNA was extracted from 125 µl of serum with Trizol LS (Invitrogen) according to the manufacturer's instructions and was resuspended in a volume of 20 µl.
|
|
|---|
|
View larger version (27K): [in a new window] |
FIG. 1. Primer design for California group Orthobunyavirus. According to the ARMS principle, the third nucleotide from the 3-prime end of a primer is the most decisive for specific binding. Shown is an alignment of the target area (sequence accession numbers) and the amplicons (FP, forward primer; P, probe; RP, reverse primer) of LACV, SSHV, and JCV. Variant nucleotides at the 3-prime ends of primers are highlighted in blue, and nonmatching nucleotides in nontarget sequences are printed in red. All sequences are given in sense orientation.
|
![]() View larger version (43K): [in a new window] |
FIG. 2. Sensitivity and specificity of the LACV amplicon. (A) Amplification blot of the LACV RNA standard from 107 to 101 molecules (from left to right: 107, blue; 106, green; 105, red; 104, black; 103, red; 102, green; and 102, blue). (B) The LACV species-specific assay was tested with 107 copies of the standard RNA of all of the other Orthobunyavirus species. The LACV amplicon showed minor cross amplification of 107 copies of the GROV standard RNA (red curve) but no cross amplification of the standard RNA of any other strain (all other colors).
|
One-step TaqMan RT-PCR. The performance of the amplicons was assessed on a standard range of 107 to 101 molecules of in vitro-transcribed -ssRNA. The sensitivities achieved with the amplicons on ABI-PRISM 7700 using RAV-2 and Tth are listed in Table 2. The addition of the single-strand binding protein GP32 of the T4 phage has been shown to increase the sensitivity of PCRs (32). The addition of GP32 increased the slope of the kinetic curves of the fluorescent signal produced in our TaqMan assays, especially in the lower standard range of 103 to 101 molecules. The increase in slope of the kinetic reaction curves allowed the threshold to be raised and placed into the elongated exponential phases of the low-copy-number standard curves of the range. This improved the correlation coefficient of the whole standard range, providing a solid basis for quantification at a higher sensitivity. We tested the standards on the LightCycler with an RNA master amplification hybridization probes kit (Roche). The results shown in Table 2 indicate that, in comparison with the results with the ABI-PRISM 7700, we found increased sensitivities of 1 to 2 logs for five species-specific TaqMan RT-PCR assays when using the Roche kit on the LightCycler. We could not generate comparable sensitivities using the Roche kit on the ABI PRISM 7700 (data not shown). Finally, we adapted all TaqMan RT-PCR assays to the SmartCycler. We again used the RAV-2-Tth enzyme mix we already had used on the ABI-PRISM 7700. We found that we had to increase the reaction temperatures to obtain good sensitivities, which on the whole were reduced by 1 to 0.5 logs compared with the performance on the LightCycler (Table 2). With our RNA standard, the nested assay for OROV showed a sensitivity of 105 RNA molecules detected in the first round of PCR and 103 RNA molecules detected in the second round of PCR in ethidium bromide stained gel analysis.
|
View this table: [in a new window] |
TABLE 2. TaqMan RT-PCR sensitivities
|
![]() View larger version (24K): [in a new window] |
FIG. 3. Detection of OROV in patient sera. (A) OROV RNA standard range from 107 to 101 molecules (as established on the SmartCycler). (B) Results are given as the number of copies of viral RNA detected per milliliter of serum obtained from each of 28 patients sampled on days 1 to 5 after onset of disease. Two patient samples drawn on days 2 and 3 after onset of disease tested negative. RNA was Trizol extracted from 125 µl of serum. OROV infection had been previously confirmed by virus isolation.
|
|
|
|---|
Most fluorescence PCR approaches settle for cloning the target area of the amplicon, since the fluorescence PCR simply measures the ratio of the fluorescent signal to the copy numbers of target molecules. The nature of the target molecule is secondary. RNA target molecules, however, tend to form complex secondary structures that reduce accessibility of the target molecule to PCR and thus influence the sensitivity of RT-PCR assays (18). In recognition of this effect, we decided to use the complete viral S segment for our RNA standard. The T4 phage single-strand binding protein GP32 has been shown to increase the sensitivity of PCR due to breakdown of secondary structures in single-stranded DNA and RNA (1, 7). GP32 indeed increased the sensitivity of our TaqMan RT-PCR assays by up to 2 logs. The RNA standards were tested on the ABI-PRISM 7700 in a Bicine buffer using RAV-2, Tth as the polymerase (23), and the additive GP32. We obtained high sensitivities for most assays. The sensitivity of the SSHV assay, however, was very low (104 to 106 molecules). One reason for this may be the extremely stable secondary structures in the S segment of SSHV. We were able to increase the sensitivities of several assays when using a RNA master hybridization probes kit on the LightCycler. One ingredient of this mixture is an aptamer-blocked Tth which allows separation of RT activity from the polymerase activity of the enzyme. The sensitivity of the LACV assay improved markedly, i.e., down to 10 molecules, when this mixture was used on the LightCycler. Compared with the use of RAV-2-Tth, the Roche mixture improved the sensitivity by just 1 additional log on the ABI-PRISM 7700. We attribute the superior efficiency of the RT-PCR in the LightCycler to the minimal transition phases between the temperatures of the PCR steps due to the fast (20°C/s) heating and cooling rates of the LightCycler.
The TaqMan amplicons performed well on the SmartCycler, although slightly reduced sensitivities compared with those for the LightCycler were obtained. Again, this may be due to the slightly reduced performance in heating (10°C/s) and cooling (2.5°C/s) of the SmartCycler compared with that of the LightCycler.
Thanks to the ARMS principle, the specificity of the assays was very good, as no cross amplification was observed when we cross tested the 11 assays with very high copy numbers of the RNA standards (107 molecules) of each of the 11 viruses. Only the LACV assay showed a minor cross amplification of the GROV RNA. However, the crossing point on the threshold for this cross amplification was very late and the fluorescence intensity was very low, i.e., the cross amplification was not very efficient. It can be ruled out by raising the threshold above a fluorescence intensity value of 0.1.
In recent years, OROV has developed into an urban disease in Amazonia and it bears all the hallmarks of an emerging disease that could quickly spread beyond its present reach (27). The OROV TaqMan RT-PCR assay showed a higher sensitivity than the established nested RT-PCR assay. It detected viral RNA in 93.3% of the 30 patient samples collected from days 1 to 5 after onset of disease, compared with 26.6% for the nested RT-PCR assay. The most likely reason for the decreased sensitivity of the nested RT-PCR assay for OROV compared with the that of the TaqMan RT-PCR assay is the differences in the amplicon sizes produced by each assay (754 and 693 bp for the first and second rounds, respectively, of the nested RT-PCR assay versus 97 bp for the TaqMan RT-PCR assay). The high mean viral load of 1.31 x 107 molecules/ml of serum is typical for infections with Bunyaviridae. In sheep, Rift Valley fever virus, for example, produces a high viremia of up to 105 viruses/ml of serum in the early days of an infection (31). An early diagnostic window for this virus is therefore amenable to RT-PCR and has also been documented for Crimean-Congo hemorrhagic fever virus (5).
The higher sensitivity of our assay allowed detection and identification of OROV in two samples collected at day 1 and in nine samples collected at day 2 of the disease. This means that patients with typical symptoms can be confirmed to be infected with OROV at a very early stage of the disease. By using our assay, rapid detection of OROV infection should indeed be possible within a total hands-on time (sampling, preparation, and PCR) of less than 3 h. This method should therefore greatly facilitate the investigation of an OROV outbreak in time to differentiate it from a dengue outbreak for which it might be mistaken. To confirm this, we are now endeavoring to collect sequential serum samples from individual patients during the next outbreak.
The combination of easy RNA extraction, mobile cyclers such as the SmartCycler TD system, and the highly sensitive and rapid one-step RT-PCRs presented here could become an ideal tool for outbreak surveillance, epidemiological screening, or detection of released biological agents in the field.
Since detection with TaqMan probes is very specific, established amplicons can only be as good as the latest sequencing information available. Especially when trying to detect RNA viruses, one should always bear in mind that a negative result only means that the sequence the amplicon has been designed for was not detected in the sample. It does not formally exclude the possible presence of a variant of the particular virus. Virus isolation and sequencing is very important to keeping fluorescent nucleic acid detection up to date. Consequently, mobile surveillance work for pathogenic RNA viruses should not rest on mobile nucleic acid detection alone. Although mobile PCR can facilitate outbreak investigation and control, it does not obviate the necessity for serology assays.
This work was supported by grants InSanI 0598-V4301 and InSanI 030-V4304 from the Bundesministerium für Verteidigung, Germany.
|
|
|---|
This article has been cited by other articles:
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Copyright © 2009 by the American Society for Microbiology. For an alternate route to Journals.ASM.org, visit: http://intl-journals.asm.org | More Info»